EPDM Butyl tapes?
Everything you want to know!

Butyl tapes for EPDM: types and concrete applications

What is an EPDM butyl tape?

Butyl tapes are self-adhesive sealing and bonding tapes based on butyl plastic, often combined with an EPDM top layer. You use them to join EPDM roofing membranes and details quickly, cleanly and watertight. A manufacturer usually develops these tapes for long-term flexibility and adhesion, so that the seal remains reliable in temperature fluctuations and weather conditions.

Success factors according to the manufacturer: preparation and processing

Whatever tape you choose, a manufacturer will always emphasise that substrate preparation determines the result:

  • Clean EPDM/TPO thoroughly: dust, grease and dirt-free.
  • Use the right primer/tape primer where the system dictates.
  • Press and roll firmly (preferably with a steel roller) to avoid air entrapment and "fish mouths".

Preferably work on dry substrates and follow the processing conditions specified by the manufacturer.

Cover Tape: masking, repairing and seam overlays

What is it? Cover Tape is usually composed of cured EPDM cover rubber with butyl plastic. It is a peel-and-stick solution that acts as an overlay.

Concrete applications:

  • Covering one or more EPDM membranes.
  • Horizontal patching of damages or cuts on the roof surface.
  • Seam repairs and seam overlays: additional sealing or strengthening of existing seams.

Practice point: choose sufficient overlap and roll the tape firmly; a manufacturer almost always recommends cleaning and priming for maximum adhesion.

Flashing Tape: penetrations, corners and complex details

What is it? Flashing Tape often consists of uncured EPDM rubber with butyl plastic. Because the material is malleable, you can shape and slightly stretch it to finish details tightly. A manufacturer chooses this type for detail work where formability is essential.

Concrete applications:

  • Penetrations: pipes, vents, cable penetrations and roof penetrations.
  • Corners: interior and exterior corners, upstands and awkward connections.
  • Detail seals where water infiltration sensitivity is high (around stacks/vents).

Practice point: work tension-free and avoid creases; model carefully and then roll hard. Works in combination with primer.

Seam Tape: fast and consistent seam joints

What is it? Seam Tape is a butyl sealer for joining roof membranes in seam applications. A manufacturer often emphasises that this enables fast installation without expensive hot-air welding equipment.

Concrete applications:

  • Longitudinal seams between EPDM membranes: controlled, reproducible overlap sealing.
  • Seam repairs: re-sealing questionable or aged overlap areas.
  • Standardisation on projects: uniform quality for larger roof areas.

Practical point: seam tape requires primer and the use of a roller is recommended. You can post-treat the edge with MS polymer if necessary.

Patches: for quick repairs

What is it? Patches are pre-formed (often round) membranes with integrated butyl plastic. Many manufacturers supply this as discs because round shapes are less likely to loosen corners.

Concrete applications:

  • Repair patches at punctures, cuts or localised leakage points.
  • T-joints: finishing junctions where seams meet.
  • Corner finishing: extra security at detail areas and transitions.

Practice point: clean and primer, roll on firmly and, if necessary, finish edges with a suitable sealant for extra security.

Perimeter Strip: along edges and perimeter of roofs or at corner transitions

What is it? Perimeter Strip is a reinforced EPDM strip with a butyl mastic seal, intended for edges and perimeter zones. A manufacturer positions this type for areas where mechanical loads and wind influences are higher.

Concrete applications:

  • Roof edges/perimeter: fixing and sealing along the entire roof perimeter.
  • Corners and upstands: transitions from horizontal to vertical.
  • Wind-critical areas: system construction with mechanical fixing (e.g. steel plates) and butyl seal.

Practice point: clean contact points (membrane and sheet) well, remove foil carefully and roll on firmly.

Which tape do you choose when?

  • Flat repairs, covering metal, seam overlay: Cover Tape.
  • Penetrations, corners, complex shapes: Flashing Tape.
  • Bonding new seams/lanes: Seam Tape.
  • Local repairs and t-joints: Patches.
  • Perimeter and wind-critical areas: Perimeter Strip.

Why Zettex is the right partner for EPDM butyl tapes

Zettex is a strong partner for EPDM butyl tapes because you are working with a manufacturer with proven experience in roofing solutions and a complete system offering. Zettex develops and produces in Europe, with production, R&D and distribution in the Netherlands, so quality, delivery reliability and product consistency can be better guaranteed than with fluctuating import flows. In addition, with Zettex you have a complete range for EPDM roofs: from Cover Tape, Flashing Tape and Seam Tape to Patches and Perimeter Strip, complemented by matching primers and supporting products. For wholesalers and processors, this means: one manufacturer, one line, reduced failure costs on the roof and a range that suits both standard work (seams and edges) and critical details (penetrations, corners and repairs).

EPDM Butyl tapes and primer Cover tape EPDM Butyl

Get in touch

Questions about our products or options? If so, please contact us.
Send a message